The sweep under Offset Path (linesweeper 0.4) never finished on some
miter offsets: on the reported glyph and on a synthetic outline it kept
allocating until the app ran out of memory. linesweeper 0.5 fixes that
infinite loop ("Fixed an infinite loop", 0.5.0 changelog), and builds
without changes.
0.5 can hand back a curve piece that doesn't follow the input curve it
was cut from. In the Shape Builder rosette test, a contour runs out along
one petal and back by such a piece, which became a 59 x 4 pt hole in the
merged shape. Tidy::repair rebuilds a piece that strays from the one input
curve through both its ends as that curve's exact sub-curve (input curves
are indexed by their bounds' left edge, so it stays cheap). The there-and-
back then encloses nothing and is dropped as a sliver. Pieces on their
curve, and pieces whose ends two input curves pass through (a real lens),
are left alone.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Transform panel has both options; the Properties panel's Transform
section had no way to them. A More Options button after the flip buttons
now opens a popup with the two (the scaleCorners / scaleStrokes prefs),
open while they are toggled.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With art selected the picker changed it only on OK. Each new colour now
previews paint.setFill / paint.setStroke on the selection through the
session interaction (the spec is preview: true): OK keeps the last one as
one undo step, Cancel puts the art back. Nothing previews until the colour
first changes, nor without a selection (the colour then only becomes the
default paint, on OK).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Lucide names its flip icons for their mirror line: flip-horizontal-2
draws a horizontal line with triangles above and below (the top-bottom
flip). The Properties and Transform panels showed it on the left-right
flip, and the other on the top-bottom one. Swapped back, with a comment.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Beside every corner of the bounding box the curved rotate cursor bowed
up. It now bows from the box's centre toward the pointer, in 45° steps
(Cursor::RotateToward, made by Cursor::rotate_about): at the top right
it opens toward the bottom left, at the bottom right toward the top left.
The Selection tool shows it over the rotate zone and while rotating (it
follows the pointer round), and Free Transform does the same.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fill_contains promised to close open subpaths (as their fill does) but
counted kurbo's winding, which leaves the closing edge out: a point beside
it read as outside. An open path (an anchor deleted from a closed one) lost
its fill clicks on that side, and a reflection moved the edge across, so it
looked like Reflect broke selection. Open subpaths are now closed by a
straight line back to their start before the winding is counted; closed
paths are borrowed as they are.
Tests: the open path from the report, on both sides and even-odd; reflected
shapes, imported SVG hearts, a selected shape dragged by its fill.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A Shift-click on a guide adds it to the selected art (guide.select
toggle keeps the art), and Shift-adding or -removing art keeps the
selected guides; a new selection still clears them. With both selected,
Delete deletes the art and the guides in one undo step (not when ids are
given).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01CC5DiGJEZ5ADaQMBEQk4W1
A PDF that names a font without embedding it (here a standard Helvetica)
is drawn with a stand-in, so comparing its glyphs with the installed
family's styles picks whichever style happens to look most like the
stand-in: with a large Helvetica family installed, Helvetica became
Helvetica CE Medium (tests_import_fidelity::text_becomes_point_type
failed on such a Mac). Fonts without a font program now keep the face
their name resolves to; embedded fonts are still compared as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01CC5DiGJEZ5ADaQMBEQk4W1
The link watch wakes the app every two seconds only while the last look
found links (068a934, #967). A file placed less than two seconds after a
look that found none asked for no more frames, so while the window sat
idle nothing stamped it; a change made meanwhile was taken for the file
as first seen and never acted on. The watch now remembers the active
document's uid and revision at each look and, when they differ on a
later frame, asks for one wake when the next look is due. There is
still no per-frame walk of the links, and no two-second wakes for a
document without links.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
$INSUNITS 22, 23 and 24 (US survey inch, yard and mile, as Autodesk's INSUNITS reference
lists them) had no size or name, so the drawing opened as unitless (millimetres, or inches
with $MEASUREMENT 0) and document.dxfInfo said Unitless.
They now derive from the US survey foot (1200/3937 m) like code 21, with their names.
The test reads each survey code's unit name and default scale and opens a survey-inch line at
7200.0144 pt.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
A root such as width="96pt" height="96" took CSS pixels (0.75 pt) along x and points along y,
so a square came in 24 x 32 pt and the artboard 96 x 96 instead of 96 x 72; with a viewBox the
art was stretched too.
When either root side is absolute, both axes now take CSS pixels at 96 per inch (usvg already
parses at that resolution): the unitless or px side is the same CSS length it would be in a
browser. The root scale is one number.
The test opens width="96pt" with height 96, 96px and 72pt, and width 128 with height 72pt: a
96 x 72 artboard and a 24 x 24 square; with viewBox 0 0 32 32 a 72 x 72 square at x 12 (meet),
and with preserveAspectRatio="none" the whole artboard.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
Cursor::precise listed every Pen state but PenJoin (added later, #794), so with Use Precise
Cursors on the Pen still showed its join badge over another open path's end.
PenJoin is a crosshair too under the preference.
The Pen join test now also checks the pointer over the other path's end is the crosshair with
the preference on (and PenJoin with it off, as before).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
shapes::polar_grid drew at least one radial divider (`radial.max(1)`), so radial 0, which
the command and the Polar Grid tool (Left arrow while dragging) accept, still drew a spoke.
Zero now draws none; the loop never divides by it.
The test checks 0, 1 and 2 radial dividers with no concentric ones give 1, 2 and 3 paths.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
Reversal read the midpoints after Gradient::reverse had reordered the stops, so each stop
took the wrong segment's midpoint: red-to-blue with its midpoint at 20% reversed to a 50%
midpoint instead of 80%, moving the transition.
Gradient::reverse now mirrors each segment's midpoint with it, so a reversed gradient is the
same ramp the other way round; paint.editGradient's own (wrong) pass is gone, and the SVG
importer's reflect spread, which had a correct copy of the same mirroring, uses it too.
Tests: two- and three-stop gradients with off-centre midpoints sample the same reversed (t vs
1 - t) and come back after two reversals; paint.editGradient reverse turns a 0.2 midpoint into
0.8.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
The menu item sends no artboard, so the engine fell back to the first one even with another
active in the Artboards panel.
The frontend fills in the active artboard (the view's, as the Artboards panel and navigator
show it) for select.allOnArtboard, as it already did for Paste in Place / in Front / in Back
(#693); the two now share one block, and the index is kept within the artboards. An explicit
artboard still wins; the engine is unchanged.
The test makes artboard 2 active, then 1, and invokes the menu item each time, then passes
artboard 1 explicitly with artboard 1 active.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
`run` reported "Broken pipe" (on Windows "The pipe is being closed") and exited 1 when the
reader of its stdout went away, unlike `commands` and the other subcommands, which end quietly.
Its step printer now treats a closed pipe as the end of output, not an error: the remaining
steps still run (an export is still written), unprinted, and the run exits 0. Other write
errors and failing steps still fail.
The test runs document.json, a rectangle and an SVG export with stdout closed: status 0, empty
stderr, the SVG written; `run --cmd not-a-command` still fails.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
The desktop app's ui.render (MCP `screenshot` when connected) always rendered the first
artboard and ignored `artboard`, which the headless backend honours.
It now renders the 0-based `artboard` (the first without one, an error for one that doesn't
exist), as headless does. control-protocol.md and the control.rs list show the parameter.
The test drives ui.render through the control channel on a 64 x 64 and a 96 x 48 artboard:
no index and 0 give 64 x 64, 1 gives 96 x 48 (48 x 24 at scale 0.5), 2 is an error.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
add_text passed `color` to text.create only, and text.createInPath built its own character
style without a colour, so type on a path and path-based area type took the current fill.
text.createInPath now uses the same new-type style as text.create (size, font, style, color,
else the current fill), and add_text sends `color` on both routes.
The MCP test draws a blue rectangle (the current fill), turns it into on-path and area type
with color #ff0000, and reads red back through inspect_document.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
With every layer hidden or locked, the insertion layer fell back to the top layer anyway, so
drawing a shape, typing, pasting, making a graph, a flare, a grid, trim marks or a symbol put
the art on a hidden or locked layer: invisible, or unselectable by Select All. Illustrator
refuses to draw on a locked or hidden target layer (public forum answers, e.g.
https://community.adobe.com/t5/illustrator/can-t-draw-a-new-object-in-my-document/m-p/11107182).
DocState::target_parent is insertion_parent for new art, failing with "the target layer is
locked or hidden" when it would be a layer that isn't editable; those creation paths use it.
Another layer that is shown and unlocked still takes the art, as before. The message is in the
de, es, fr, it, ja, ru and uk catalogs. File > Place is left as it is (another branch reworks
it).
The test hides, then locks, the only layer: an ellipse, a polar grid, text and a paste each
fail with the message and leave the document unchanged; a new layer then takes a rectangle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
Character and paragraph styles checked a new attribute against the keys its base style
serializes, and the JSON leaves out Auto leading and kerning, no mojikumi and other defaults.
So charStyle.new / setAttrs refused leading or kerning, paraStyle.new refused mojikumi, and a
style captured from text with explicit leading failed to apply to Auto-leading text, to
duplicate or to come back out of a library.
The check now also accepts every field name the style type deserializes (read from serde's
derive), still refusing unknown keys and the file-only justify_auto.
The test creates and edits styles with kerning, leading, small caps, mojikumi and direction,
applies a captured leading style to fresh text with and without Clear Overrides, duplicates it,
uses it from a library, and checks `nope` and `justify_auto` are still refused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
# Conflicts:
# ROADMAP.md
Asset Export, File › Export, Save for Web and Object › Rasterize drew
each shape with its own smoothed edge, so where two shapes met edge to
edge (Divide, Shape Builder, abutting art) both half-covered the pixels
on the line and the background showed through as a thin ghost border.
With Art Optimized (the default) these now supersample, as the option's
name in Illustrator says: the art is drawn with hard edges at four times
the size (three or two times for large images, within a 40-megapixel
budget and the renderer's 65,535-pixel side) and each block averaged
into one pixel. Pixels shared by two shapes are fully owned by one or
the other at the finer size, so no seam is left, and the outer edges
are still smooth. The canvas keeps shape-by-shape smoothing for speed;
None and Type Optimized are unchanged.
RenderOptions::supersample turns it on (exports and Rasterize set it).
A render test checks two triangles sharing a diagonal: a seam with
shape-by-shape smoothing, none supersampled, and the factor's limits.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
bflatastic
lloyd
mateususa
redrun6767
Katt